Focusrite Octopre 8 Input Preamp + ADAT I/F Bundle

The Platinum OctoPre provides eight pristine discrete channels of Focusrite Class A mic pre and compression, OctoPre routes directly to any digital audio workstation via eight standard analogue outputs, or via a choice of two optional 24-bit, 96kHz A/D converters (see below for details). The new OctoPre offers the unique qualities associated with the Focusrite name at an affordable price. Each channel features a revolutionary compressor/limiter circuit, providing a warm-sounding compressor, which morphs into a brick wall limiter to avoid those critical overs, ensuring total control over all eight channels.

The mic pres featured in OctoPre are the same as those featured elsewhere in the award winning Focusrite Platinum range. They are a transistor-based Class A design utilising the same full-bandwidth philosophy as the legendary Red and ISA mic pres, ensuring detail and clarity without colouration. The first two 'super channels' also feature phase reverse, as well as TRS jack inputs on the front fascia for quick and easy, DI-free instrument plug-in.

Eight line level balanced (+4 dBu) analogue inputs and outputs are provided as standard via 25-pin D-type connectors. These D-type connectors may be routed to 8 XLRs by means of an 8-way 25-pin D-type to 8 XLR breakout cable, available separately. In addition to the analogue outputs, the OctoPre can be fitted with one of the following two digital output options:

24-bit/96 kHz ADAT; interface card

This card provides digital outputs for all eight OctoPre channels, which operate over the full sample frequency range (44.1, 48, 88.2 and 96 kHz) and can be dithered to 16-, 20-, or 24-bit depths depending upon the destination. External word clock synchronisation is possible using the rear panel BNC connector. The card features two ADAT;-type lightpipe output connectors. For speeds up to 48KHz both connectors transmit all 8 channels simultaneously. However, ADAT;-type connectors are bandwidth limited at sample rates above 48 kHz - each audio channel uses two ADAT; digital channels to accommodate the increased quantity of data, hence the need for two ADAT; connectors to allow 8 channels of conversion at high speed.

Specifications

Inputs

Electronically balanced 20kW
Nominal level +4dBu / -10dBV

Input Connectors

1/4? jack (channels one and two only)
25 pin D-type 8 channel line level analogue connector
8 XLR inputs for Mic

Front Panel Controls

Phantom Power: On/Off: +48V
Gain (mic): 0dB to 60dB
Gain (line): -10dB to +10 dB
Gain (instrument): 0dB to 60dB (Impedance > 1MOhm)
Phase Reverse: On/Off (Channel 1 & 2 only)
High Pass filter: On/Off: -12dB / octave. ?6dB at 75Hz
Dynamics: Limiter threshold is fixed at 20dBu. Compressor threshold and ratio is variable
Frequency select: Switchable (44.1, 48, 88.2, 96kHz)
Dither: 24-, 20- or 16-bit

Metering

Signal Present: -20dBFS (green LED)
Overload: +22dBu (red LED)
Compressor mode: Yellow LED intensity increases with compression
Hard Limit mode: Red LED on when limiting (threshold = +20dBu)

Analogue Output

25-pin D-type 8 channel analogue connector

Performance specifications

THD: 0.001% @ 20dBu input, mic and line at 0dB gain
Noise: -96dB at unity gain through the unit
Mic EIN: -128 dBu @ 6dB of gain with 150Ohm termination impedance
Frequency response: -1dB at 10Hz to 200kHz
Dimensions
480mm (w) x 44mm (H) x 265mm (D)
Weight
3.2kg